🔍 Click to zoom
3M Protecta PRO Twin-Leg Shock Absorbing Lanyard — 1340180
$108.99
Final price set by Amazon · may vary
EDITORIAL REVIEW: 4.7/5 — WC Safety Review of the 3M Protecta PRO Twin-Leg 1340180, a Y-leg rebar-hook lanyard for 100% tie-off. Editorial assessment by Steven Eaton, WC Safety editor, based on published 3M specific...
Check Price on Amazon🔒 Amazon Associate · You pay the same price · We earn a small commission
Zero Sponsored ListingsNo paid placements. Rankings are never sold or influenced by manufacturers.
Independent Product ResearchBuilt from manufacturer specifications, published standards information, and cited sources
Standards MatterRatings and markings vary by model and variant — verify the manufacturer’s documented rating for your hazard
Built for Industrial BuyersResearch written for safety managers, procurement teams, and field supervisors.
EDITORIAL REVIEW: 4.7/5 — WC Safety Review of the 3M Protecta PRO Twin-Leg 1340180, a Y-leg rebar-hook lanyard for 100% tie-off.
Editorial assessment by Steven Eaton, WC Safety editor, based on published 3M specifications and category fit. We did not laboratory-test this product.
Editorial assessment by Steven Eaton, WC Safety editor, based on published 3M specifications and category fit. We did not laboratory-test this product.
The 3M Protecta PRO Twin-Leg 1340180 is an OSHA 1926.502 and ANSI Z359.13 compliant Y-leg shock-absorbing lanyard with rebar hooks on each leg, enabling 100% tie-off — one leg stays clipped while the worker clips the other to the next anchor. Its PRO Pack shock absorber limits arresting force below the 1,800-lb OSHA limit, protecting both worker and harness during an arrest.
CHECK PRICE ON AMAZON → SHOP LANYARDS →
As an Amazon Associate, WC Safety earns from qualifying purchases.
Why the 3M Protecta PRO Twin-Leg keeps you always connected
A single-leg lanyard leaves a dangerous gap every time you move: unclip, cross, reclip — and for those seconds you are unprotected. The PRO Twin-Leg closes that gap with a Y configuration and rebar hooks on each leg, so one leg stays anchored while you clip the other to the next point before releasing the first. That is 100% tie-off, and the large rebar hooks clip over bar, scaffolding, and members a standard snap hook cannot. The PRO Pack shock absorber keeps arresting force below the 1,800-lb OSHA limit, and the polyester webbing handles the weather. As lanyards go, this is the continuous-connection pick, and the best fall protection lanyards guide and fall protection equipment guide cover how the pieces fit. It is the lanyard for workers on the move at height.
Safety first: this lanyard is only one component of a complete personal fall arrest system — it must be paired with a compatible ANSI Z359.11 full-body harness at the dorsal D-ring and anchors rated for at least 5,000 lb per OSHA 1926.502(d)(15). Twin-leg use gives continuous connection, but the clearance math still applies to the arresting leg: calculate free fall, the roughly 3.5 ft deceleration distance, D-ring height, and a safety factor before work. Retire the lanyard after any fall or visible damage, and inspect before every use. Confirm requirements with the OSHA 1926 fall protection guide.
What the 3M Protecta PRO Twin-Leg listing documents
From the published specs: OSHA 1926.502 and ANSI Z359.13 compliance; a twin-leg Y configuration with rebar hooks for 100% tie-off; a PRO Pack shock absorber below the 1,800-lb OSHA limit; 6 ft; and polyester webbing. These are true twin leg lanyard credentials and a genuine 100% tie-off lanyard — a certified shock absorbing lanyard for continuous connection.
How the 3M Protecta PRO Twin-Leg compares to other lanyards
For a tie-back single option, the 3M Protecta PRO Tie-Back or FallTech WrapTech; for other Y-leg 100% tie-off, the FallTech 8259Y or Guardian 01230; for a single-leg value option, the Guardian 01220; and for a premium Y-leg, the Petzl Absorbica Y. The safety harness guide pairs the harness.
Building a complete fall arrest system
A lanyard is one of three parts. For the harness, the full-body harnesses collection; for anchors, the anchor points collection and roof anchors guide; for complete sets, the fall protection kits collection and kits guide; and the full fall protection collection plus self-retracting lifelines span every category.
Where it fits by job and crew orders
The PRO Twin-Leg suits steel erectors, roofers, and construction crews who move between anchors and need continuous protection — compare tool-lanyard options in the tool lanyards collection for dropped-object control. Follow the manufacturer's instructions on parking the unused leg, and retire the lanyard after any fall. For crew orders, quantity purchasing runs through a free Amazon Business account — volume pricing, PO numbers at checkout, and tax-exempt eligibility for qualifying organizations, with the walkthrough linked in our footer.
Frequently asked questions
What is the 3M Protecta PRO Twin-Leg 1340180?
An OSHA 1926.502 and ANSI Z359.13 compliant Y-leg shock-absorbing lanyard from 3M's Protecta PRO Pack series, with rebar hooks on each leg for 100% tie-off during construction, roofing, and elevated work.
What is 100% tie-off?
With a twin-leg Y lanyard, one leg stays clipped to the current anchor while you clip the other leg to the next anchor before unclipping the first - so you are never disconnected while moving, closing the gap where a single-leg lanyard leaves you unprotected.
What are rebar hooks for?
Rebar hooks are large-opening hooks that clip over reinforcing bar, scaffolding, and structural members that a standard snap hook will not fit, which is why they are common on construction and concrete work.
How does the shock absorber work?
The PRO Pack shock absorber deploys during a fall to limit the maximum arresting force to well below the 1,800-lb OSHA limit under 29 CFR 1926.502(d)(16)(iv), reducing the load on the worker and the harness.
What harness and anchor do I need?
Connect the harness end to the dorsal D-ring of an ANSI Z359.11 full-body harness and each leg to a certified anchor rated for at least 5,000 lb per OSHA 1926.502(d)(15). The lanyard alone is not a complete system.
How much fall clearance do I need?
Calculate total fall clearance before work: free fall, the roughly 3.5 ft deceleration distance, D-ring height, and a safety factor. Twin-leg use does not change the clearance math for the leg that arrests a fall.
Can I clip both legs to one anchor?
Clip only the working leg during normal work; the second leg is for the transition between anchors. Follow the manufacturer's instructions - some configurations restrict parking the unused leg on the harness.
What is the webbing made of?
Polyester webbing that resists UV, abrasion, and jobsite chemicals, helping it endure outdoor construction and roofing over its service life.
When must it be retired?
Retire the lanyard immediately after it arrests a fall - the shock absorber is spent - or if the webbing, stitching, or hardware shows cuts, burns, corrosion, or deformation. Inspect before every use.
Does it need inspection?
Yes - inspect the webbing, stitching, shock pack, and hooks before each use, and have a competent person perform documented periodic inspections per your fall-protection program.
What work is it for?
Construction, roofing, steel erection, and elevated work where workers move between anchor points and need continuous connection with rebar-compatible hooks.
How do I order for a crew?
Quantity purchasing runs through a free Amazon Business account - volume pricing, PO numbers at checkout, and tax-exempt eligibility for qualifying organizations. The bulk-ordering walkthrough is linked in our site footer.
Read our detailed 3M Protecta PRO Twin-Leg Shock Absorbing Lanyard review — strengths, limitations, and the alternatives that matter.
Brand / Vendor
3M
Model / SKU
1340180
Product Type
Lanyard
Price
$108.99 (Amazon)
Rating
4.3 / 5 — 11 Amazon ratings
Availability
Check current availability on Amazon
No Paid Placements
Every product earns its place on documented safety credentials and specifications — never advertising spend.
Industrial Grade Only
Coverage focuses on equipment built for professional use in manufacturing, construction, and industrial environments.
Independent Product Research
Product information is compiled from manufacturer specifications, published standards information, compatibility data, and other cited sources.
Affiliate Disclosure
WC Safety may earn commissions from qualifying purchases made through affiliate links. Affiliate relationships never change the specifications presented.
Verified Buyer Reviews
Customer Reviews
★★★★☆4.3 / 5· 11 ratings on Amazon
★★★★★
Five Stars
Great lanyard, distinct color mean i always know what one is mine.
Verified Purchaser · August 28, · ✓ Amazon Verified Purchase
Showing 1 of 11 Amazon reviews.
Share Your Experience
Write a Review
Thank you for your review!
Your submission has been received and will be published after verification.
Frequently Asked Questions
What is the 3M Protecta PRO Twin-Leg 1340180?
An OSHA 1926.502 and ANSI Z359.13 compliant Y-leg shock-absorbing lanyard from 3M's Protecta PRO Pack series, with rebar hooks on each leg for 100% tie-off during construction, roofing, and elevated work.
What is 100% tie-off?
With a twin-leg Y lanyard, one leg stays clipped to the current anchor while you clip the other leg to the next anchor before unclipping the first - so you are never disconnected while moving, closing the gap where a single-leg lanyard leaves you unprotected.
What are rebar hooks for?
Rebar hooks are large-opening hooks that clip over reinforcing bar, scaffolding, and structural members that a standard snap hook will not fit, which is why they are common on construction and concrete work.
How does the shock absorber work?
The PRO Pack shock absorber deploys during a fall to limit the maximum arresting force to well below the 1,800-lb OSHA limit under 29 CFR 1926.502(d)(16)(iv), reducing the load on the worker and the harness.
What harness and anchor do I need?
Connect the harness end to the dorsal D-ring of an ANSI Z359.11 full-body harness and each leg to a certified anchor rated for at least 5,000 lb per OSHA 1926.502(d)(15). The lanyard alone is not a complete system.
How much fall clearance do I need?
Calculate total fall clearance before work: free fall, the roughly 3.5 ft deceleration distance, D-ring height, and a safety factor. Twin-leg use does not change the clearance math for the leg that arrests a fall.
Can I clip both legs to one anchor?
Clip only the working leg during normal work; the second leg is for the transition between anchors. Follow the manufacturer's instructions - some configurations restrict parking the unused leg on the harness.
What is the webbing made of?
Polyester webbing that resists UV, abrasion, and jobsite chemicals, helping it endure outdoor construction and roofing over its service life.
When must it be retired?
Retire the lanyard immediately after it arrests a fall - the shock absorber is spent - or if the webbing, stitching, or hardware shows cuts, burns, corrosion, or deformation. Inspect before every use.
Does it need inspection?
Yes - inspect the webbing, stitching, shock pack, and hooks before each use, and have a competent person perform documented periodic inspections per your fall-protection program.
What work is it for?
Construction, roofing, steel erection, and elevated work where workers move between anchor points and need continuous connection with rebar-compatible hooks.
How do I order for a crew?
Quantity purchasing runs through a free Amazon Business account - volume pricing, PO numbers at checkout, and tax-exempt eligibility for qualifying organizations. The bulk-ordering walkthrough is linked in our site footer.