XPOWER P-230AT Mini Mighty Air Mover — 925 CFM, 1/4 HP Induction, 3-Hour Timer, 3-Speed

As an Amazon Associate, WC Safety earns from qualifying purchases. This does not affect the price you pay.

What the XPOWER P-230AT Mini Mighty Air Mover Is

It is a compact centrifugal floor dryer that moves up to 925 CFM, driven by a 1/4 HP induction motor that draws about 2.3 amps, with three speeds, four drying positions (0, 20, 45 and 90 degrees), a 3-hour timer plus an Always-On mode, two onboard power outlets, a built-in 12-amp circuit breaker, a 10-foot cord, and a weight of about 10.2 pounds. It stacks with a handle and daisy-chains. It is the step up from the 600 CFM P-80A: more airflow, a durable induction motor, and the timer and breaker the smaller model does not have.

Like any air mover, it is the drying step of a wet job — you remove the water with a wet-vac or carpet extractor first, then the mover sweeps the residual moisture off the surface. It is still a utility-class mover for room and small-area drying, not a flood or structural dryer (that is a 5,000 CFM job), and not an air scrubber (that HEPA-filters air). It does not heat air or extract water. Browse all janitorial equipment.

More Airflow and a Timer: Stepping Up from the P-80A

The P-230AT and the P-80A are the two compact XPOWER movers to weigh against each other, and the differences are real. The P-230AT pushes 925 CFM from a 1/4 HP induction motor against the P-80A's 600 CFM from a smaller motor, so it clears a larger damp area or dries faster. It adds a 3-hour timer — set it and it shuts off on its own, ideal for unattended or overnight drying — and a built-in 12-amp circuit breaker on its onboard outlets, neither of which the P-80A has. The induction motor is the quieter, run-all-day type.

The trade is amps. At about 2.3 amps per unit versus the P-80A's 1.2, the P-230AT pulls nearly twice the current, so you can chain fewer of them on one circuit — the honest rule is to divide the circuit's amperage by 2.3 and leave headroom, not to assume the smaller model's chain count. So the split is clear: pick the P-230AT for more airflow, the timer and the built-in breaker; pick the P-80A for the lightest, lowest-draw unit you can chain more of. Both are the drying step after a carpet extractor, and both should run with wet floor signs out while the area dries; our carpet-extractor guide covers the water-removal step.

Pros & Cons

Specifications

Related Guides

Related Products

Frequently Asked Questions

How does the P-230AT compare to the P-80A?

The P-230AT is the step-up model. It moves 925 CFM against the P-80A's 600, runs a 1/4 HP induction motor rather than the smaller motor, and adds a 3-hour timer and a built-in 12-amp circuit breaker the P-80A does not have; it also weighs a bit more (about 10.2 vs 7.9 pounds) and draws more current. Choose the P-230AT for more airflow, unattended timed drying and the built-in breaker; choose the P-80A when you want the lightest, lowest-draw unit and can chain more of them.

What does the 3-hour timer do?

You can set the P-230AT to run for three hours and then shut itself off automatically, or leave it in Always-On mode to run continuously. The timer is genuinely useful for drying: set it and walk away, and the mover stops on its own rather than running all night, which saves energy and wear. It is one of the main reasons to pick this model over the timer-less P-80A when you dry areas unattended or overnight.

What do the induction motor and 1/4 HP mean?

An induction motor has no carbon brushes to wear out, so it runs cooler and quieter and holds up to long, continuous duty better than a brushed motor — a good match for a machine that may run for hours drying a floor. At 1/4 HP driving up to 925 CFM, it is a meaningful step up in airflow from the smaller P-80A. It is a durable, run-all-day motor rather than a burst-of-power one.

How many can I daisy-chain?

Fewer than the P-80A — and this is the key electrical point. The P-230AT draws about 2.3 amps per unit, nearly double the P-80A's 1.2, so fewer fit on one circuit. Do the math: divide the circuit's amperage by 2.3 and stay under it, leaving headroom. The onboard 12-amp circuit breaker protects the chain plugged into the outlets, but the wall circuit's rating is the real limit. Never assume the smaller model's chain count carries over.

What is the built-in circuit breaker for?

The P-230AT has a 12-amp circuit breaker built into its onboard power outlets. If the units you chain into it draw more current than the outlets can safely pass, the breaker trips and cuts power rather than overheating the wiring — a protection the smaller P-80A does not include. It is a helpful safeguard for daisy-chained fleets, but it does not replace sizing your chain to the wall circuit; treat it as a backstop, not a license to overload.

Is 925 CFM enough for a big area?

It covers a larger area than the 600 CFM P-80A and suits a good-sized room or a few units chained across a floor, but it is still a portable utility mover, not a flood or structural-drying machine. A burst pipe, a flooded building or whole-structure drying needs high-CFM units such as a 5,000 CFM air mover run in numbers. Use the P-230AT for routine floor and carpet drying at a step up in power, and scale to a bigger machine for disaster-level water.

What are the four positions for?

The housing tilts to 0, 20, 45 and 90 degrees, including a kickstand angle, so you can aim the airflow at what you are drying — flat across a floor, angled up a wall or cove, or upright as a spot fan or to move air up a stairwell. Matching the angle to the surface is how you get the most drying out of the airflow, whichever mover you use.

Can I stack them for storage?

Yes — the P-230AT stacks with a carry handle, so several store on a shelf or in a vehicle and carry easily, the same fleet-friendly design as the rest of the Mini Mighty line. Between the stackability, the onboard outlets and the timer, it is built to deploy in numbers around a job and pack down small afterward.

How do I dry carpet after extraction with it?

Extract the water first with a carpet extractor or wet-vac — the mover dries residual moisture, it does not pull water out. Then position movers around the damp carpet at a low angle, set the timer, and let them run; move them as areas dry. The extra airflow over the P-80A clears a room-sized damp area faster, and drying carpet promptly after extraction is what prevents the mildew and odor damp carpet develops.

Does it heat the air or extract water?

No — like any air mover it moves ambient air to speed evaporation, with no heater and no suction. Remove the standing water with a wet-vac or extractor first, then run the P-230AT to dry what remains. And it is not an air scrubber: an air scrubber filters room air through a HEPA element for air quality, which is a different machine and a different job from drying a floor.

What are the electrical and safety points?

Size the daisy chain to the circuit, since at 2.3 amps per unit fewer fit than with the P-80A; keep the cord and unit out of standing water; run it on a GFCI-protected circuit on wet floors; and route cords clear of trip paths. The timer lets you leave it running unattended, but that does not change the cord-and-water rules. Because you are often drying a just-cleaned floor or a water-damage site, the cleaning and restoration chemicals in the job are a chemical splash risk, so wear gloves and eye protection.

What is the XPOWER P-230AT not?

It is not a flood or structural dryer (that needs high-CFM units run in numbers), not an air scrubber (that HEPA-filters air), not a heater or water extractor, and not just a box fan. It is a 925 CFM utility air mover with a timer and a built-in breaker for room and small-area floor and carpet drying — the step up from the P-80A. Extract the water first, size the chain to the circuit amps, aim it with the positions, and wear PPE for the chemicals in the job.