Bullard C33 Full Brim Hard Hat - Type II Class E, HDPE, 6-Point Ratchet, Made in USA
$25.48
Final price set by Amazon · may vary
Color: Black
EDITORIAL REVIEW: 4.5/5 WC Safety Review — Bullard C33 Full Brim Hard Hat, HDPE, 6-Point Ratchet, Made in USA Editorial assessment by the WC Safety Editorial Team, based on published Bullard specifications and cat...
Check Price on Amazon🔒 Amazon Associate · You pay the same price · We earn a small commission
Zero Sponsored ListingsNo paid placements. Every recommendation is based on compliance, build quality, and field performance.
Curated SelectionExpert-chosen safety gear
Independently ReviewedUnbiased assessments — no manufacturer input
Built for Industrial BuyersSourced and reviewed for safety managers, procurement teams, and field supervisors.
EDITORIAL REVIEW: 4.5/5 WC Safety Review — Bullard C33 Full Brim Hard Hat, HDPE, 6-Point Ratchet, Made in USA
Editorial assessment by the WC Safety Editorial Team, based on published Bullard specifications and category fit. We did not laboratory-test this product.
Bullard C33 Full Brim Hard Hat - Type II Class E, HDPE, 6-Point Ratchet, Made in USA Overview
The Bullard C33 Full Brim Hard Hat is a Type II, Class E head protection system built around a tough high-density polyethylene (HDPE) shell and a 6-point ratchet suspension, proudly Made in the USA. The full 360-degree brim sheds rain, sun, and falling debris around the entire circumference, giving it an edge over cap-style hats for outdoor and overhead work.
Under ANSI/ISEA Z89.1, the Type II classification means this hat is impact-tested for both top and lateral (side, front, and rear) impact, not just the crown - important wherever swinging loads, slips, or struck-by hazards come from off-axis. The Class E rating provides dielectric protection tested to 20,000 volts, making the C33 appropriate for electrical, utility, and high-voltage environments. Because Class E integrity depends on a solid shell, the C33 is non-vented - never substitute a Class C (vented) hat near energized conductors.
The 6-point ratchet suspension distributes impact energy across more contact points than a 4-point and dials in a secure, repeatable fit with a one-hand rear knob. Browse more full-brim hard hats or compare the full hard hats range, and confirm your rating with the hard hat selection guide. Per OSHA 1910.135, retire and replace any hard hat after a significant impact or once it passes the date code molded inside the shell.
What It Is Built For
| Use case | Fit | Buyer guidance |
|---|---|---|
| Electrical and utility work (up to 20kV) | Ideal | Class E dielectric rating to 20,000V makes the C33 a correct choice for energized environments; keep it non-vented. |
| Construction with overhead / struck-by hazards | Ideal | Type II top + lateral impact protection covers off-axis strikes; full brim adds debris shedding. |
| Outdoor / sun-exposed jobsites | Ideal | 360-degree full brim sheds rain and shades the neck and ears better than a cap style. |
| Hot / high-airflow indoor work needing ventilation | Not suitable | The C33 is non-vented to preserve its Class E rating; choose a Class C vented hat only where there is no electrical hazard. |
| Confined overhead clearance / tight cap-style fit | Consider alternative | A full brim adds width; a cap-style hard hat may clear tight spaces better. |
A hard hat protects only if it fits and is in date. Match the impact type (Type I top-only vs Type II top + lateral) and electrical class (Class E 20kV / G 2.2kV / C conductive — never wear Class C near electrical) to the hazard. Adjust the suspension for a snug, level fit, inspect the shell and suspension before each use, and replace at the manufacturer date code (shells about 5 years, suspensions about 12 months from first use, and immediately after any impact). OSHA 29 CFR 1910.135 / 1926.100 requires head protection where objects may fall. See how to adjust a hard hat suspension and hard hat classes explained.
Pros & Cons
Pros
- Type II rated for both top and lateral impact, not just crown strikes
- Class E dielectric protection tested to 20,000 volts for electrical work
- 6-point ratchet suspension spreads impact load and gives one-hand fit adjustment
- Full 360-degree brim sheds rain, sun, and debris all the way around
- Durable HDPE shell, Made in the USA
Cons
- Non-vented, so it runs warmer than a vented Class C hat in hot conditions
- Full brim is wider than a cap style and can catch in tight overhead clearances
- Must be replaced after any impact or at the molded date code per OSHA 1910.135
How It Compares
Within the Bullard full-brim family, the C33 and the Bullard S61 cap-style hard hat (HDPE, 4-point ratchet) share the same Type II / Class E ratings and HDPE shell, but differ in two ways: the C33 has a 360-degree full brim versus the S61's cap-style front-only brim, and the C33 steps up to a 6-point ratchet suspension versus the S61's 4-point - more contact points for load distribution. Choose the full-brim C33 for outdoor sun and rain shedding; choose the cap-style S61 for tighter overhead clearances. For other Class E full-brim options, compare the Ergodyne 8971 Skullerz full-brim (Class E) and the Klein Tools KARBN non-vented full-brim (Class E). See the full lineup of full-brim hard hats.
Specifications
| ANSI Type | Type II (top + lateral impact) |
| ANSI Class | Class E (electrical, tested to 20,000V) |
| Brim Style | Full brim (360-degree) |
| Suspension | 6-point ratchet |
| Shell Material | High-density polyethylene (HDPE) |
| Vented | No (non-vented to preserve Class E rating) |
| Accessory Slots | Bullard accessory-compatible shell |
| Origin | Made in USA |
| Standard | ANSI/ISEA Z89.1-2014 |
Related Resources
hard hats cap-style hard hats full-brim hard hats vented hard hats safety helmets hard hat selection guide hard hat classes explained how to adjust a hard hat suspension bullard s61 cap style hard hat hdpe 4 po msa v gard h2 full brim safety helmet wi
Frequently Asked Questions
Is the Bullard C33 a Type I or Type II hard hat?
It is a Type II hard hat, meaning it is impact-tested under ANSI/ISEA Z89.1 for both top and lateral (side, front, and rear) impact, not just the crown.
What is the electrical rating of the C33?
The C33 is Class E, providing dielectric protection tested to 20,000 volts, which makes it appropriate for electrical, utility, and high-voltage work.
Is the Bullard C33 vented?
No. The C33 is non-vented. Vents would compromise its Class E dielectric rating, so it is built as a solid shell. Use a vented Class C hat only where there is no electrical hazard.
Can I use the C33 near energized electrical conductors?
Yes, within its rating. As a Class E hat it is tested to 20,000 volts. Never substitute a Class C (conductive/vented) hat near electrical hazards, and follow your site's electrical safety program.
What suspension does the C33 use?
It uses a 6-point ratchet suspension. The six contact points distribute impact energy and the rear ratchet knob lets you adjust fit with one hand.
How is the 6-point suspension different from a 4-point?
Six suspension points spread impact load across more contact areas of the head than four. For step-by-step setup, see our guide on how to adjust a hard hat suspension.
What shell material is the C33 made from?
The shell is high-density polyethylene (HDPE), a tough, impact-resistant thermoplastic. The C33 is made in the USA.
What is the difference between the C33 full brim and a cap-style hard hat?
The C33 has a 360-degree full brim that sheds rain, sun, and debris all the way around and shades the neck and ears. A cap-style hat has a front-only brim and is narrower for tight overhead clearances.
How does the C33 compare to the Bullard S61?
Both are Type II / Class E HDPE hats. The C33 is full-brim with a 6-point ratchet; the S61 is cap-style with a 4-point ratchet. Choose the C33 for outdoor coverage, the S61 for tight clearances.
When do I need to replace the C33?
Per OSHA 1910.135, replace any hard hat immediately after a significant impact and retire it at the shell date code. Inspect regularly for cracks, dents, or UV damage.
Is the C33 compatible with Bullard accessories?
Yes. The shell is designed to work with Bullard's accessory ecosystem. Use only manufacturer-approved accessories so the hat keeps its ANSI rating.
Does the full brim help in rain and sun?
Yes. The 360-degree brim sheds rain away from the face and neck and provides shade around the full circumference, which a front-only cap brim cannot match for outdoor work.
Written by Steven Eaton, WC Safety Editorial. Specifications sourced from Bullard published data. Compare the range in hard hats.
WC Safety is an independent PPE retailer and Amazon Associate; no paid placement. Match the product to your specific hazard and follow your site PPE program.
Brand / Vendor
Bullard
Model / SKU
33BKR
Product Type
Hard Hat
Price
$25.48 (Amazon)
Rating
3.78 / 5 — 9 reviews
Availability
Check current availability on Amazon
No Paid Placements
Every product earns its place based on safety credentials and field performance, not advertising spend.
Industrial Grade Only
Products sourced for professional use in manufacturing, construction, and industrial environments.
Compliance Verified
Every product listed on WC Safety is reviewed for standards compliance and safety credentials before publication.
Sourced for Professionals
Gear selected for safety managers, procurement teams, and field supervisors — not casual consumers.
Verified Buyer Reviews
Customer Reviews
★★★★☆4.1 / 5· 97 ratings on Amazon
★★★★★
Nice Product. Good Value
I use it as a waterproof rain hat cuz the price was right—I bought the cheapest color. Maybe it might protect me from an owl attack. Not actually kidding either. A female jogger was attacked by a Barred Owl last week just south of me. Required stitches.But back to the hat—do not try to attach the suspension system w/o watching a YouTube video. I can almost guarantee you'll get it wrong and maybe even wreck your hat if you try to use force or power tools.Anyway, it's a perfectly fine hardhat—good quality, nice finish, good fit, but watch the video: "Bullard Wildland Helmet Suspension" to stay happy with your purchase.
Verified Purchaser · November 1 · ✓ Amazon Verified Purchase
★★★★★
Highly recommended seller
Great price for the safe provided by hat. Got the color I wanted and shown in website.
Verified Purchaser · August 14, · ✓ Amazon Verified Purchase
★★★☆☆
se mira en casco las hendiduras de las entradas del ajustador de la cabeza como positos
Verified Purchaser · April 19, · ✓ Amazon Verified Purchase
★★★★☆
Four Stars
A bit difficult to a simple
Verified Purchaser · December 2 · ✓ Amazon Verified Purchase
★★☆☆☆
Hard to assemble.
Wrong color... ordered green, got black. Pain in the butt to assemble.
Verified Purchaser · January 31 · ✓ Amazon Verified Purchase
★★★★★
Good Product
This helmet fits snug and is sturdy. The webbing did NOT come assembled to the hard hat which would have been nice. Haven't gotten bonked on the noggin yet so I can't say how that part work but it seems like it could take a pretty good blow w/o a problem.
Verified Purchaser · April 23, · ✓ Amazon Verified Purchase
★★★★★
Hard hat
I use it for work..I'm a shipyard Structural Welder. It fits, feels and looks great. Thank you
Verified Purchaser · February 7 · ✓ Amazon Verified Purchase
★★☆☆☆
Am I missing something
I mean it’s a hard hat but it’s the wrong color and usually have bought these in the past they come with chinstraps? I did separate order for a pink one which was right color but still had no chin strap. Hope this helps someone
Verified Purchaser · October 10 · ✓ Amazon Verified Purchase
★★★☆☆
Wrong color.
Fine hard hat, but it’s not the color I ordered. I ordered green ,but got black instead.
Verified Purchaser · February 1 · ✓ Amazon Verified Purchase
Showing 9 of 97 Amazon reviews.
Share Your Experience
Write a Review
Thank you for your review!
Your submission has been received and will be published after verification.