Moldex 7000 Series Half Mask Respirator — 7001 Small, 7002 Medium, 7003 Large

As an Amazon Associate, WC Safety earns from qualifying purchases. This does not affect the price you pay.

What the Moldex 7000 Series Half Mask Respirator Is

A reusable half facepiece built around few parts and easy maintenance: an adjustable head harness for a custom fit, bayonet mounts that take cartridges without fuss, a wide field of vision for a half mask, and a light weight that matters more the longer a shift runs. Moldex formulates it without PVC, natural rubber latex, or silicone — three exclusions that each solve a real problem, as covered below. The three part numbers are purely sizes: 7001 small, 7002 medium, 7003 large.

What it does not do on its own is protect you from anything. The facepiece is a carrier; the cartridge you fit determines the hazard covered, and all three sizes take the same 7000 Series range. Organic vapour work takes the 7100, acid gas the 7200, both together the 7300, ammonia and methylamine the 7400, several gas families at once the 7600 multi-gas Smart cartridge, and particulate alone the 7740 P100.

Choosing Cartridges: Combination or Separate

Once the hazard is identified, the remaining decision is whether to run a combination cartridge or keep gas and particulate separate. Combination cartridges build a P100 into the gas cartridge — the 7367 for organic vapour and acid gas, the 7467 for ammonia and methylamine, the 7667 for multi-gas. One part per side, nothing to assemble wrongly, and the right answer when dust and vapour are both present all the time.

Keeping them separate suits work where particulate comes and goes: you run gas cartridges as the baseline and add particulate filtration only when the dusty task arrives, replacing a loaded filter without discarding unused sorbent capacity. Neither approach is better in the abstract — it depends on whether your two hazards actually coincide. If you are still deciding between platforms entirely, the half mask comparison guide and when do you need a respirator are the places to start, and the rest of the range sits in Moldex half masks.

Pros & Cons

Specifications

Related Guides

Related Products

Frequently Asked Questions

Which Moldex cartridge should I fit for my hazard?

Match the cartridge to the contaminant. Organic vapour work takes the 7100; acid gas takes the 7200; both together take the 7300. Ammonia and methylamine take the 7400. For several gas families at once, the 7600 multi-gas Smart cartridge covers the range. For particulate alone, the 7740 P100 filter. The facepiece is identical in every case — the cartridge is what determines your protection.

Can I get gas and particulate protection in one cartridge?

Yes, and it is usually the tidier answer when both hazards are present. Moldex offers combination cartridges that build a P100 into the gas cartridge: the 7367 for organic vapour and acid gas, the 7467 for ammonia and methylamine, and the 7667 for multi-gas. The alternative is fitting a separate particulate filter, which suits work where dust is only occasionally present.

Do all three sizes take the same cartridges?

Yes. The 7001, 7002, and 7003 differ only in facepiece size — all three accept the same 7000 Series cartridges and filters. That matters for stocking a mixed crew: you buy the sizes your people need but keep a single cartridge inventory rather than one per size.

Can I fit 3M or Honeywell cartridges on it?

No. Moldex is explicit that you cannot interchange parts from different brands of respirators or substitute parts from another manufacturer. This is not simply about whether something physically mounts — NIOSH approval covers the respirator and its cartridges as a tested assembly, so mixing platforms voids the approval even if the parts appear to fit.

Why does it matter that it is silicone-free?

Mostly in paint and coatings work. Silicone transfers readily from surfaces to work and causes fisheyes and adhesion defects in paint finishes, which is why many body shops ban silicone-containing products from the booth entirely. Moldex builds the 7000 facepiece without silicone, and also without PVC and natural rubber latex, which sidesteps that contamination risk as well as latex sensitivity concerns.

How should I put it on and check the seal?

Position the facepiece over the nose and mouth, draw the head harness over the crown, and adjust the straps so the mask sits firmly without being over-tightened — a mask cranked down hard is a sign of the wrong size, not a good seal. Then do a user seal check every time: block the cartridges and inhale gently so the facepiece draws slightly toward your face and holds. Do this before every entry, not just on the first day.

What if no size seals properly on me?

Then a tight-fitting respirator is not the right equipment for you, and the answer is not to persevere with a poor seal. Facial structure, scarring, and facial hair along the sealing surface can all prevent a reliable seal. Loose-fitting powered air-purifying respirators and supplied-air hoods exist precisely for those cases, and a fit test is what determines which category you belong in.

How do I clean and store the facepiece?

Remove the cartridges first, then clean the facepiece per Moldex's instructions and let it dry fully before reassembly. Store it sealed in a clean bag away from the work area — not hanging on a nail in the shop, where it collects the very contamination you are trying to avoid breathing. Storing it with cartridges attached in a contaminated area quietly consumes cartridge life.

When does the facepiece itself need replacing?

Inspect it before each use rather than on a calendar: look for cracking, hardening, or distortion of the facepiece, perished or stretched harness straps, and damage to the valves and sealing surfaces. Any of those means retirement. The facepiece is the reusable part, but reusable is not permanent, and a hardened sealing edge will fail a fit test long before it looks obviously broken.

Does it work with safety glasses and a hard hat?

Generally yes, and half masks are chosen partly because they leave the eyes clear for whatever eyewear the job needs. Check the combination on the actual wearer, though — spectacle temples crossing the sealing surface can break the seal, and that is a fit issue rather than a comfort one. Where eye protection must also seal, a full facepiece solves both problems at once.

Is it suitable for lead or asbestos work?

Those are regulated substances with their own OSHA standards, and the respirator is only one part of what those standards require — exposure assessment, decontamination, medical surveillance, and specified protection factors all apply. The correct cartridge class for those particulates is P100. Do not treat a half mask plus filters as a complete compliance answer for regulated abatement work.

How does a reusable facepiece compare on cost to disposables?

The facepiece is a one-off purchase that lasts through many cartridge changes, so the running cost is cartridges rather than masks. Against disposable respirators, reusables win on long-term cost and on sealing consistency for regular wearers, and lose on convenience for occasional or visitor use. Crews that wear protection daily generally end up on reusables for exactly that reason.