Insulated Electrical Gloves

Which insulated electrical gloves should you buy in 2026?

Short answer: The MAGID Class 0 rubber insulating gloves (rated per ASTM D120 for up to 1,000 V AC per the class marking) worn under the MAGID leather protectors — the two-layer system is mandatory, not optional. Budget both plus the 6-month electrical retest OSHA 1910.137 requires.

Insulated Electrical Gloves (2026)

Rubber insulating gloves are the one glove category where the glove is a calibrated instrument: ASTM D120 voltage classes, date-stamped test cycles, and a mandatory leather outer layer. This collection carries the Class 0 system that covers most commercial and industrial low-voltage work — the shock-protection lane of the glove wall, alongside cut, chemical, and welding protection.

Editor's pick — MAGID Class 0 Insulating Gloves
The ASTM D120 Class 0 barrier for LV electrical work — worn under leather protectors, air-tested before every use, retested on the 1910.137 clock. (Affiliate link — see disclosure below.)

VIEW MAGID CLASS 0 INSULATING GLOVES → CHECK PRICE ON AMAZON →

What this collection covers

• The dielectric layer — MAGID Class 0 rubber insulating gloves.
• The mandatory outer layer — MAGID leather lineman protectors.

Shop electrical gloves on Amazon → Class 0 Gloves Leather Protectors

The program around the glove

OSHA 1910.137 sets the rules: leather protectors over rubber, electrical retest at maximum 6-month in-service intervals, air-test and visual inspection before each use, and ozone-safe storage. Gloves are the last line — energized-work permits and the lockout/tagout discipline come first. We've deliberately started this category with the Class 0 system; higher voltage classes and ATPV-rated arc-flash kits are a different program tier we'll add against demand.

Frequently asked questions

What does Class 0 mean on electrical gloves?

ASTM D120 voltage classes rate insulating gloves; Class 0 covers use up to 1,000 V AC per the class marking on the MAGID Class 0 gloves — the class that covers most commercial/industrial LV electrical work. Higher classes (1-4) serve utility voltages.

Why do rubber electrical gloves need leather protectors?

The rubber is the dielectric barrier and the leather takes the mechanical abuse — a pinhole from a burr is an invisible failure in the only layer between you and the circuit. OSHA 1910.137 expects protectors over insulating gloves; the MAGID leather protectors are that layer.

How often must insulating gloves be electrically retested?

OSHA 1910.137 requires in-service insulating gloves to be electrically retested at intervals not exceeding 6 months (12 months for gloves that have been tested but not issued). Date-stamp the cuffs and calendar the retest.

How do I field-check electrical gloves before use?

Air test: roll the cuff to inflate the glove and watch/listen for leaks, plus a visual check for cuts, ozone cracking, and embedded debris — before every use. Any doubt retires the pair until retest.

Are these arc-flash rated?

Voltage insulation and arc-flash thermal protection are different ratings — these gloves address shock, not the thermal event. Arc-flash PPE is a separate category we've deliberately not stocked yet; program-level arc work needs a full ATPV-rated kit.

Who needs Class 0 gloves?

Electricians and maintenance techs working at or near energized LV circuits under an electrical safety program. Pair with insulated tools and the lockout discipline in our lockout/tagout collection — gloves are the last line, not the plan.

How should insulating gloves be stored?

Cuff-up, undistorted, away from ozone sources (motors, sunlight) — folded or compressed storage creates the stress cracks that fail air tests. The bag they ship in is the storage plan.

What sizes do insulating gloves come in?

Sized like work gloves but fit matters doubly: too tight stresses the rubber, too loose costs dexterity near energized parts. Check the listing's size run and size to your measured hand.